Frequently ask questions

1. How does alcohol/water injection work?

By injecting a fine spray of alcohol/water into the inlet air stream of the engine, the charge air is dramatically cooled and the effective octane of the fuel is raised. Both help to eliminate detonation — the enemy of any engine, especially those using today's lower octane fuel under boost.


2. How much timing and/or boost will i be able to increase with water methanol injection?

There is no rule of thumb on how much  timing or boost can be increased when running water methanol injection system.  Each engine will react to it differently. In general  most engines you can usually run the equivalent  boost and timing of your  100 octane tune.  While on  pump gas and with a  50/50 mix of water methanol.


3. Can alcohol/water injection damage my motor?

Not if installed and used properly. As long as the injection system is working properly, it can only do good things. Since the alcohol will dissolve carbon buildup, It will help keep your plugs, valves, and combustion chambers very clean.


4. My turbo/supercharged engine runs standard boost, would alcohol/water injection increase the horsepower?

5. Do your kits come with a tank?

All of our kits ship without a tank, but include the fittings to convert your existing washer tank for use with our system. Additional tanks can, however, be purchased separately here on this site. We want to let you have the options of what size tank if you need one.


6. I would like to increase my power output by increasing the boost pressure. Would alcohol/water injection help then?

7. What kit should I get, Stage 1 or Stage 2?

Our DevilsOwn Stage 1 "Base" injection kit incorporates a boost switch that activates the system at a specific PSI. It’s adjustable from 2-10 psi or 6-30psi, but you can run up to 250 PSI through the switch, so it’s very reliable. This system will turn on at a level you set and stay on until you drop below that level. It’s On/Off. It can’t dial in exact flow, but it can get you within a range.

DevilsOwn Stage 2 "Progressive" kits offer high functionality and performance, the ability to vary the flow based on inputs (maf, map, tps, ait, any 0-5v source). Most users run it off of separate GM style map sensor if there car does not already have a map sensor. With the Stage 2 Kit you set a starting boost and a full boost and the system will progressively adjust the flow between those two points.

Both styles work. We tell our customers that if budget is the primary concern, get the base injection kit. If you have a little more money to spend or want something with more user control, the progressive kit is worth it.


8. How much alcohol/water do I need spray?

Most cars should aim for 15% of their total fuel flow. Some more extreme setups run as much as 25% of their total fuel flow.


9. What liquid should i run in this system?

We recommend DevilsOwn Brew, our proprietary methanol blend. Not only does methanol improve your fuel quality, it will also give you a better intercooling effect in the inlet tract.

Denatured alcohol can be used but we strongly advise our customers to use methanol for better, more consistent performance.


10. What is the maximum alcohol/water ratio your system can handle?

The wetted components in the pump head are chemically compatible with 100% methanol and denatured alcohol. Components are engineered to withstand 100% mixtures for the normal expected life of the product. We recommend not running more than 50/50 mix of water and methanol or other alcohol blends, to reduce the risk of fire and improve consistency and performance.


11. Does the water "burn" in the engine?

No. The water simply converts from a vapor to a gaseous state which absorbs huge amounts of heat, due to the energy required to transform it.


12. What supporting upgrades are required for alcohol/water injection?

At minimum, your vehicle should have some sort of engine management that can be tuned, for example, the ability to adjust timing, boost, and fuel curves to compensate for the octane boost and cooling effects, and the ability to take advantage of the adjustments to make power.

You can run alcohol/water injection on a stock car with tunable engine management. It is not necessary to have after-market intakes, exhausts, intercoolers, or strengthened internals. However, with supporting mods that already increase the volumetric efficiency of the engine, more power can be made.


13. Has my order shipped?

Click the "My Account" link on our site to check your orders status.


14. Why not use a windshield washer pump?

Alcohol/water must be injected at above 50psi to properly atomize. Pressure lower than 50psi causes greatly reduced air charge cooling as the result of larger droplets and their reduced total surface area.


15. How do I track my order?

You should get an email from us with the tracking number. If you did not and your status in "My Account" link on our site shows shipped. Get your order number and click on this link to track your package.


16. My order is missing parts.

Click the "My Account" link on our site to track your order status. Click on your order number and read the comments on your order. If there is no mention of back ordered parts then please contact us.


17. When will my backorder arrive?

Backordered items are those which our suppliers are unable to predict when they will have more in stock, but as soon as they do, we will be able to ship the item to you.


18. How do I create an account in the store?

1) Click the "Log In " button to proceed.
2) Click the "Create Account " button at the right bottom.
3) Enter your information, and make sure you use your the address where you recieive your credit card statement at.
4) Click the "Proceed" button to continue.


Your information is NEVER sold to any other company and is kept completely private. Please view our Privacy Policy for more information. You may then login to the "My Account"section and update your password to anything you prefer.


19. How do I edit my account information?
20. How do I edit my address / ship to an alternate address?
21. How much is my shipping?

Shipping is automatically calculated prior to submitting your payment information. Simply add items to your cart and proceed to the Checkout page where you will be offered Shipping Method choices and their prices.


22. When will my order ship?

We make every effort to ship all orders the same day they are ordered. Also, after placing your order, you may click the "My Account" link on our site to track the status of your order.


23. My Order Never arrived?

Click the "My Account" link on our site to track your order status. Be sure that all of the items in your order have shipped already. If your order displays your Package Tracking Numbers, check with the shipper to confirm that your packages were delivered.


24. Do you ship to my country?

DevilsOwn ships to nearly every country. Please refer to shipping options while ordering.


25. What are my payment choices?

Our online ordering system currently accepts Visa, Mastercard, and Discover. If you wish to use an alternate payment method such as PayPal or a Wire Transfer, please after registering for an account email us. During the checkout process you may choose any of our current payment options and continue to place your order. Please note that we will not ship your order until we receive payment from you.


26. I need a copy of my receipt/invoice.

Click the "My Account" on our site to review your order history.


27. What temp does X% of methanol freeze at?

100% Methanol is good to -100 degrees F
50/50% of Water /Methanol is good to -68 degrees F
75/25% of Water/Methanol is good to -25 degrees F


28. What is the brass piece with the tank tap?

Insert the brass piece into the tubing before inserting the tubing into the tank tap. This is used for tube support.


29. Which nozzle do I have?

All nozzles sizes are listed on the side of the nozzle, flow numbers are listed under each nozzle description.


30. How do I install the nozzle?

Using an 11/32” drill bit, drill a hole at the selected location. If drilling through thicker metal like a throttle body or an intake manifold, use a 1/8” NPT tap. If going through thinner material, the nozzle can sometimes just thread right into it. Alternatively, you can have a 1/8” NPT bung welded in at any exhaust shop.


31. How do I install my nozzle into the nozzle holder?

Insert the filter side into the nozzle holder. The nozzle should turn by hand 1/2 way, then only need another 1-2 turns with a wrench to achieve a leak free seal.


32. Can I mount my pump higher than my tank?

We recommend mounting your tank at the same level as the tank, or below the tank.


33. Where can I mount my pump?

The pump can be mounted at any angle. Make sure to mount the pump away from heat, moisture/liquid and road debris.


34. How can I mount a nozzle into silicone tubing?

When mounting a nozzle into silicone tubing, a nozzle mounting adapter would be used.


35. Can I clean the filter on the nozzle?

The filter can be cleaned by simply removing the screen off the nozzle then soaking it in some lime away for about 15-30 min. Make sure to rise the nozzle to remove the chemicals.


36. How do I remove the blue tabs out of the pump?

Push down on the collar around the blue tubing. Then slightly pull on the tabs.  Pushing down on the collar allows the fiting to let go of the tubing.


37. Can I use windshield washer fluid?

Yes, methanol does go bad. It naturally will absorb moisture out of the air if its not in a sealed container. You should always store methanol in a cool dry place away from direct sunlight.


38. What is the freezing point of methanol alcohol mixed with water?

Take your Methanol \ Water Mixtures Concentrate to determine the freezing point of your mixture. Winter is here and you should make sure your not going to have a freezing's problem with your water methanol injection system.

Methanol Information

Methanol (METHYL ALCOHOL) Concentrate
Vol.% ---Freezing Point,F ---Flash Point,F


0----------32f--------No Flash
13---------20f --------130f
24---------0f ---------110f
35---------15f---------95f
46 --------40f---------85f
56---------65f---------75f
66---------95f---------70f
75---------115f--------60f
83---------125f--------55f
92---------130f--------55f
100--------144f--------55f

Other tid bits about methanol:
Boiling Point: 147F,64C
Melting/Freezing Point: : -144F,-98C
Vapor Pressure: 760 Vapor Density: 1.1
Specific Gravity: 0.8


39. Does methanol go bad?

Yes methanol does go bad. It naturaly will absorb moister out of the air if its not in a sealed container. You should always store methanol in a cool dry place away from direct sunlight.


40. Who would benefit from water/meth injection?

Everyone! With the chemical intercooling and octane increase, you can run more boost, more timing, and leaner AFRs, all which lead up to more power. You could easily run 1-2 more PSI, 2-3 degrees more timing, and AFRs in the 11.5-12:1 range, while having a "safer" tune


coolingmist

In to media

DevilsOwn In the Magazines

DevilsOwn Injection has been featured in endless magazines, websites, videos, and on TV.

Nozzle choose