Progressive Install on an Audi S4

voytas · 12-05-2007

I'm familiar with MRC Tuning. Did you track your car or dyno it with the WI and without it, what gains did you notice and how much your IAT and EGT's lowerd in temp?

noggy · 12-06-2007

The code was just done to my liking remotely given my HW setup. Newer did any dynoruns as I dont see the point. I do FATS runs and with these cold temps meth does not affect power IMO. Iats keep about 5F delta and EGTs under the 945 C treshold. I'm pushing this engine so my FATS times are deep under 3sec.

ENDEE666 · 08-01-2008

What did you use to seal the pickup in the washer fluid res?

noggy · 08-01-2008

Just the provided rubber washer. hasn't leaked yet

ENDEE666 · 08-01-2008

No additional silicon or epoxy?

noggy · 08-01-2008

IIRC I didn't have silocon available and desided to try without ant it holds just fine

voytas · 08-01-2008

I used epoxy on my. I would recommend doing the same. You don’t want something popping out and loosing fluid if you tuned for methanol.

12-05-2007	#21 (permalink)
voytas Water Injection Newb Year: 2000 Make: audi Model: s4 Join Date: Dec 2007 Posts: 6	Re: Progressive Install on an Audi S4 I'm familiar with MRC Tuning. Did you track your car or dyno it with the WI and without it, what gains did you notice and how much your IAT and EGT's lowerd in temp? Last edited by voytas; 12-05-2007 at 04:32 PM.

12-06-2007	#22 (permalink)
noggy Water Injection Newb Year: 1999 Make: audi Model: s4 Join Date: Aug 2007 Posts: 9	Re: Progressive Install on an Audi S4 The code was just done to my liking remotely given my HW setup. Newer did any dynoruns as I dont see the point. I do FATS runs and with these cold temps meth does not affect power IMO. Iats keep about 5F delta and EGTs under the 945 C treshold. I'm pushing this engine so my FATS times are deep under 3sec.

08-01-2008	#23 (permalink)
ENDEE666 Water Injection Newb Year: 2001 Make: Audi Model: A6 2.7T Stg 3 6M Join Date: Aug 2008 Posts: 3	Re: Progressive Install on an Audi S4 What did you use to seal the pickup in the washer fluid res?

08-01-2008	#24 (permalink)
noggy Water Injection Newb Year: 1999 Make: audi Model: s4 Join Date: Aug 2007 Posts: 9	Re: Progressive Install on an Audi S4 Just the provided rubber washer. hasn't leaked yet

08-01-2008	#25 (permalink)
ENDEE666 Water Injection Newb Year: 2001 Make: Audi Model: A6 2.7T Stg 3 6M Join Date: Aug 2008 Posts: 3	Re: Progressive Install on an Audi S4 No additional silicon or epoxy?

08-01-2008	#26 (permalink)
noggy Water Injection Newb Year: 1999 Make: audi Model: s4 Join Date: Aug 2007 Posts: 9	Re: Progressive Install on an Audi S4 IIRC I didn't have silocon available and desided to try without ant it holds just fine

08-01-2008	#27 (permalink)
voytas Water Injection Newb Year: 2000 Make: audi Model: s4 Join Date: Dec 2007 Posts: 6	Re: Progressive Install on an Audi S4 I used epoxy on my. I would recommend doing the same. You don’t want something popping out and loosing fluid if you tuned for methanol.