[Boostedpimp]

Anybody use -an braided lines for there Alcohol setup?? I had a razor kit (WWW ALKYCONTROL.COM) awhile back and liked the braided lines.. especially as hot as it can get under my hood. Not a fan of the plastic lines so im wondering if anybody's converted and what sizes/fitings they've used because im a noob with -an stuff

[pacemkr86]

i just ordered a set of lines and reservior from Razzor to convert a Devils Own kit over to stainless lines.. it was like 200 bucks with resevior and all the lines from the tank to the pump and feed lines to the dual nozzles

[dvldoc]

Originally Posted by Boostedpimp

Anybody use -an braided lines for there Alcohol setup?? I had a razor kit (WWW.ALKYCONTROL.COM) awhile back and liked the braided lines.. especially as hot as it can get under my hood. Not a fan of the plastic lines so im wondering if anybody's converted and what sizes/fitings they've used because im a noob with -an stuff

Unless the lines are directly sitting on a exaust manifold they will have no issues. Inside braided stainless steel lines is a nylon tube or teflon lined with a nylone tube, it is not metal. So what I use is the stainless steel line covering in my vehicle because of how it is routed in the engine. It looks just like the stainless lines after your done and it cost about 1/10 th the price. Mcmaster carr carries it as well as a few other places.

Or you can go with this Bentley Harris Convoshield Chrome Corrugated tubing

You got to remember the hose we sell has a higher heat tolerance and strenth than any hose in your vehicle. It will outlast the car and any other vac line, belt, radiator hose ect. If your worried about heat areas use the covershield. If you can burn through that than you got it laying on a header.

But everyone likes it there own way, There are other and much cheaper places to get the same line as alkycontrol uses. You just have shop around there are many local places that can do you custom lengths for less than $5 a foot with the fittings. The an style fittins can be gotten on mcmaster carr for under $2 bucks each. all the fitting they use can be gotten on there.

[pacemkr86]

i used alkycontrol , cause they had the reservior i needed with the all the fittings and low level sensor already built it.. but still using the DO pump and controller

[Boostedpimp]

Originally Posted by dvldoc

Unless the lines are directly sitting on a exaust manifold they will have no issues. Inside braided stainless steel lines is a nylon tube or teflon lined with a nylone tube, it is not metal. So what I use is the stainless steel line covering in my vehicle because of how it is routed in the engine. It looks just like the stainless lines after your done and it cost about 1/10 th the price. Mcmaster carr carries it as well as a few other places.

Or you can go with this Bentley Harris Convoshield Chrome Corrugated tubing

You got to remember the hose we sell has a higher heat tolerance and strenth than any hose in your vehicle. It will outlast the car and any other vac line, belt, radiator hose ect. If your worried about heat areas use the covershield. If you can burn through that than you got it laying on a header.

But everyone likes it there own way, There are other and much cheaper places to get the same line as alkycontrol uses. You just have shop around there are many local places that can do you custom lengths for less than $5 a foot with the fittings. The an style fittins can be gotten on mcmaster carr for under $2 bucks each. all the fitting they use can be gotten on there.

Thanks for the info.. My downpipe gets really hot really quick and it's driven allot on the weekends and sometimes during the week so I was thinking of just replacing it with -an line and be done with it.. no worries of it melting and an engine fire erupting you know but using some shielding makes sense.

That Bentley Harris stuff looks good.. I was actually looking at the DEI stuff earlier today.. i'l have to compare pricing and most likely go with that