Nozzle Questions

MR T · 06-18-2008

I am looking to get the outside mount nozzles but i was wondering what would be needed to attach the inlet side to say a -4 an line . I want to use the braided line on the pressure side . I really dont trust the push in plastic line already blew one out on the dyno ( My Fault ) it was not fully locked in . Luckly no Fire ( running straight meth )

Also I am running a 2.0L 4g63 With GT42R @ 32 PSi car is making 625 HP 93 octane with straight meth Running a 550cc nozzle . I am still having a hard time getting my knock down . I think I just need to inject more meth .
The Calculator estimates about 14gph . Should i install 2 nozzles ore just one? I think 2 is my best option . Then I can swap out sizes easier .

My goal is around 700WHP on this set-up @ around 38-40 Psi can it be done ? Any recomendations?

dvldoc · 06-18-2008

You just need 3/8npt to 4an style fittings and 1/8npt to 4an style fitting. There also called flare tube fittings (45 degree) You can actually find them in homedepot or Ace hardware.

But once you place the push to connect fitting in correctly they will never come loose.

MR T · 06-19-2008

Ok so I need a -4 fitting with 3/8 Female end on it ? Just want to make sure before I order them .

I am also thinking of getting 2 14gph nozzles . I think that should be good for 700+ Hp at or over 40 psi ? with room to go higher if needed ?

06-18-2008	#1 (permalink)
MR T Water Injection Newb Year: 1999 Make: Mitshubishi Model: Eclipse GSX Join Date: May 2008 Posts: 4	Nozzle Questions I am looking to get the outside mount nozzles but i was wondering what would be needed to attach the inlet side to say a -4 an line . I want to use the braided line on the pressure side . I really dont trust the push in plastic line already blew one out on the dyno ( My Fault ) it was not fully locked in . Luckly no Fire ( running straight meth ) Also I am running a 2.0L 4g63 With GT42R @ 32 PSi car is making 625 HP 93 octane with straight meth Running a 550cc nozzle . I am still having a hard time getting my knock down . I think I just need to inject more meth . The Calculator estimates about 14gph . Should i install 2 nozzles ore just one? I think 2 is my best option . Then I can swap out sizes easier . My goal is around 700WHP on this set-up @ around 38-40 Psi can it be done ? Any recomendations?

06-18-2008	#2 (permalink)
dvldoc DevilsOwn Staff Join Date: Apr 2005 Posts: 1,884	Re: Nozzle Questions You just need 3/8npt to 4an style fittings and 1/8npt to 4an style fitting. There also called flare tube fittings (45 degree) You can actually find them in homedepot or Ace hardware. But once you place the push to connect fitting in correctly they will never come loose. __________________ Deploying to Iraq Aug 2008

06-19-2008	#3 (permalink)
MR T Water Injection Newb Year: 1999 Make: Mitshubishi Model: Eclipse GSX Join Date: May 2008 Posts: 4	Re: Nozzle Questions Ok so I need a -4 fitting with 3/8 Female end on it ? Just want to make sure before I order them . I am also thinking of getting 2 14gph nozzles . I think that should be good for 700+ Hp at or over 40 psi ? with room to go higher if needed ?